EMS 7703 Bedienerhandbuch

SYSTEM 7000 7940 HIGH POWERED UHF CONTACT OPERATED TRANSMITTER INSTALLATION AND PROGRAMMING INSTRUCTIONS

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 10 Now select the following settings: - Once completed, click on the ‘Apply’ button an

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 11 Now select ‘Call’ and ‘Disconnect and the screen will change to display: - Now select ‘Fil

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 12 Now select the ‘Settings’ tab and the screen will change as below: - The Settings should b

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 13 Once the settings are as above, click on the ‘ASCII Setup‘ button and check tha

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 14 Once the settings are as above, click on the ‘OK’ button then on the next window click on the

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 15 7. CON 7.1 Each of the transmitters inputs can be programmed to operate via a normally open

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 16 10. Adding A Transmitter Into The IRIS Radio Receiver The following sequence of operations is

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 17 10.10 Activate the transmitters onboard tamper switch and observe the screen will

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 18 11. Assigning Text Description For A Transmitter 11.1 Repeat steps 10.1 to 10.4. 11.2 Pres

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 19 11.11 By using the “4” button to move left or the “6” button to move right, move to the letter

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 2 Table of Contents Section

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 20 13. Internal Input Wiring

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 21

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 22 EMS Group Head Office Technology House, Sea Street Herne Bay, Kent CT6 8JZ England Tel:

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 3 1. Introduction 1.1 The high powered contact operated UHF transmitter has been designed to op

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 4 3. Equipment Required: 7940 Contact Operated Transmitter 7256 IRIS Receiver with standard 7200

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 5 Figure 2 7940 Half Watt Txer 7940 Half

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 6 4. Programming Connection Details 4.1 The computer to transmitter physical connection detail

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 7 5. Transmitter Programming 5.1 The transmitter unit has the facility of changing it’s inpu

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 8 Now enter your desired connection description: - Then click on the ‘OK’ button, and the

EMS 7000 IRIS + 7940 ENGINEERS GUIDE v2.2 – 13/04/10 9 Now select the Comm Port required as below: -